Meta: Wondering How To Reduce Microphone Noise? This Article Will Walk You Through The List Of The Most Effective Ways To Get crystal-Clear Audio.
Table of Contents
Intro
A microphone’s level of noise can sabotage a flawless sound recording. Want to learn how to reduce microphone noise? We have prepared a list of 8 methods you can apply to get the optimal audio records. Check it out to find out what you can do to minimize or eliminate all the annoying noise from your mic.
How To Reduce Microphone Noise
You might wonder how many ways to reduce mic noise. This article will introduce you to the top 8 most effective ways to lessen the unwanted noise in your audio.
Utilize Shock Mount
A shock mount efficiently isolates a microphone from the boom or stand to which it is mounted. Thus, your microphone will be less vulnerable to shock or mechanical noise.
You may find many shock mount products for microphones on the market falling into the following primary categories:
- External Shock Mounts: These microphone clips are of the “skeleton” or “basket” variety used in studios. You can attach it to your boom/stand to keep your mic in position.
- Internal Shock Mounts: These are incorporated into the mic and aid in mechanically isolating the cartridge or capsule from the microphone’s body.
Notice that the function of these two types is the same. They both can significantly lessen the intensity of vibrations that pass through solids and reach the mic capsule.
Turn To Balanced Microphone Cable
The audio signal is sent over two conductors instead of one using balanced connections. While operating, one signal is inverted polar opposite to the other (one negative and one positive). Once it arrives at the destination, the negative will be modified to positive and merged with the original signal.
Meanwhile, the noise on the negative is also turned and turns into the opposite of the noise on the positive. Any noise that both conductors equally picked up is therefore discarded.
As a result, you will find it has nearly no external noise or distortion while using a balanced mic cable. It also brings a higher signal-to-noise ratio and substantially lower impedance transmissions.
Use Radio Frequency (RF) Filter
RF filters allow or block specific frequencies or signals to reduce noise or the passage of undesired signals. In other words, an RF filter is made to enable the transmission or attenuation of various frequencies that would be used.
The design of an RF filter makes it possible to operate with ease throughout a wide frequency range, including megahertz and gigahertz. Due to how an RF filter operates, it is frequently employed in gadgets like televisions, broadcast radios, and wireless communication systems.
Utilize A Pop Filter
A noise-canceling filter for microphones, also known as a pop filter, is most frequently used in recording studios. During recorded singing or speaking, it helps to lessen or completely remove popping noises brought on by mechanical impact. Pop filters come in three different main categories.
- Nylon Mesh Filters: This nylon-material type is the most common due to its effectiveness and affordability.
- Metal Mesh Filters: More expensive than the former option because of the metal material, these items, however, filter a larger frequency range while minimizing or removing plosive sounds.
- Foam Windscreens: These are mostly used for lavalier and outdoor boom mic. Still, the two above options are more efficient at cutting down plosive sounds since the foam windscreens might be too close to the microphone to function effectively.
Take Advantage Of Clean Microphone Preamps
A mic preamp is a device created to add gain to your mic signal and output it at line level. Microphones must be preamplified when utilized with recording equipment or digital audio workstations because they emit mic level signals.
Employing clean mic preamps is crucial if you want the best audio quality. Most mic preamps can offer sufficient clean gain to raise the signal from an active mic to line level without appreciable noise introduction.
Notice that the mic signal does get colored by certain professional preamps. In fact, the mic signal will be colored by any analog electronics.
Buy Noise-Canceling Microphone
A high-quality noise-canceling mic speaks volume if you want to create optimal audio. Should you be confused about which product to choose among hundreds of options out there, we highly recommend the TONOR noise-canceling mic.
With its noise suppression, it will help get rid of nearly all background and self-created noise, bringing you the crystal-clear record sound. The mic also comes with a 3.5mm jack, allowing you to listen to the content that has been captured in real-time without any echo.
Move Your Microphone Closer
Want to know how to reduce microphone noise without preparing additional devices? Just bring your mic closer.
Getting close to your mic lessens the need to increase the microphone’s sensitivity to compensate for the distance. To put it another way, if you stand too far from the microphone, you will need to boost the microphone’s sensitivity, which also raises noise levels.
When speaking, place the microphone 1 to 3 inches (around 2.5 to 7.6 cm) from your mouth to get the best sound. This is because the chance that the microphone may pick up distorted air noise increases with the distance between it and your mouth. Suppose the sound becomes too loud while bringing your mic close; lowering the gain will solve the problem.
Record In A Soundproof Space
Record In A Soundproof Space Will Reduce Unwanted Noise.
This is an obvious way to eliminate your microphone noise to a certain extent. It would be best if you could record in a soundproof booth, which includes padded interior walls that help to produce an environment that is acoustically dead and free of surface reflections.
If you can’t go to a professional studio, you can still create a soundproof space in your own home. Simply use soundproofing foam and carpeting to cover the walls and the floor. You may also hang more curtains and soundproofing boards on your walls to lessen noise in the space.
Wrapping Up
Nothing is more annoying than setting up a microphone for a recording only to discover that it’s filled with odd noises. Now you know how to reduce microphone noise.
As you can see, one of the most effective ways to lessen the unwanted noise is to use a noise-canceling mic, such as the TONOR microphone. Also, apply the other methods above, and you will soon see a big improvement in your final products.